R03S (01005) S-Series, Low ESR Capacitor Multi-Layer High-Q Capacitors
Specifications
| Electrical Specifications |
|---|
| Case Size: |
01005 |
| Capacitance: |
0.2 - 10 pF |
<< Back to R03S
| Mechanical Characteristics |
|---|
| Size |
Units |
Length |
Width |
Thickness |
End Band |
| 01005 |
In |
.016 ± .001 |
.008 ± .001 |
.008 ± .001 |
.006 Max. |
| Mechanical Specifications |
|---|
| |
Specification |
Test Parameters |
| Solderability: |
Solder coverage = 90% of metalized
areas No termination degradation |
Preheat chip to 120°-150°C for 60 sec., dip terminals in rosin flux then dip in Sn62 solder @ 240°±5°C for 5±1 sec |
| Resistance to Soldering Heat: |
No mechanical damage
Capacitance change: ±2.5% or 0.25pF
Q>500 I.R. >10 G Ohms
Breakdown voltage: 2.5 x WVDC |
Preheat device to 80°-100°C for 60 sec. followed by 150°-180°C for 60 sec. Dip in 260°±5°C solder for 10±1 sec. Measure after 24±2 hour cooling period |
| Terminal Adhesion: |
Termination should not pull off. |
Linear pull force* exerted on axial leads soldered to each terminal. *0402 = 2.0lbs, 0603 = 2.0lbs (min.) |
| PCB Deflection: |
No mechanical damage.
Capacitance change: 2% or 0.5pF Max |
Glass epoxy PCB: 0.5 mm deflection |
<< Back to R03S
| Environmental Specifications |
|---|
| |
Specification |
Test Parameters |
| Life test: |
No mechanical damage.
Capacitance change: ±3.0% or 0.3 pF
Q>500 I.R. >1 G Ohms
Breakdown voltage: 2.5 x WVDC |
Applied voltage: 200% rated voltage, 50 mA max.
Temperature: 125°±3°C
Test time: 1000+48-0 hours |
| Thermal Cycle: |
No mechanical damage.
Capacitance change: ±2.5% or 0.25pF
Q>2000 I.R. >10 G Ohms |
5 cycles of: 30±3 minutes @ -55°+0/-3°C,
2-3 min. @ 25°C, 30±3 min. @ +125°+3/-0°C,
2-3 min. @ 25°C
Measure after 24±2 hour cooling period |
| Humidity, Steady State: |
No mechanical damage.
Capacitance change: ±5.0% or 0.50pF max.
Q>300 I.R. = 1 G-Ohmbr /> Breakdown voltage: 2.5 x WVDC |
Relative humidity: 90-95%
Temperature: 40°±2°C
Test time: 500 +12/-0 Hours
Measure after 24±2 hour cooling period |
| Humidity, Low Voltage: |
No mechanical damage.
Capacitance change: ±5.0% or 0.50pF max.
Q>300 I.R. = 1 G-Ohm min.
Breakdown voltage: 2.5 x WVDC |
Applied voltage: 1.5 VDC, 50 mA max.
Relative humidity: 85±2% Temperature: 40°±2°C
Test time: 240 +12/-0 Hours
Measure after 24±2 hour cooling period |
| Vibration: |
No mechanical damage.
Capacitance change: ±2.5% or 0.25pF
Q>1000 I.R. = 10 G-Ohm
Breakdown voltage: 2.5 x WVDC |
Cycle performed for 2 hours in each of three perpendicular directions.
Frequency range 10Hz to 55 Hz to 10 Hz traversed in 1 minute. Harmonic motion amplitude: 1.5mm. |
<< Back to R03S
| Capacitance Values* |
|---|
| Value (pF) |
Cap Code |
Tolerances |
|
Value (pF) |
Cap Code |
Tolerances |
| 0.2 |
OR2 |
A, B, C, D |
|
2.4 |
2R4 |
A, B, C, D |
| 0.3 |
OR3 |
A, B, C, D |
|
2.7 |
2R7 |
A, B, C, D |
| 0.4 |
OR4 |
A, B, C, D |
|
3.0 |
3R0 |
A, B, C, D |
| 0.5 |
OR5 |
A, B, C, D |
|
3.3 |
3R3 |
A, B, C, D |
| 0.6 |
OR6 |
A, B, C, D |
|
3.6 |
3R6 |
A, B, C, D |
| 0.7 |
OR7 |
A, B, C, D |
|
3.9 |
3R9 |
A, B, C, D |
| 0.8 |
OR8 |
A, B, C, D |
|
4.3 |
4R3 |
A, B, C, D |
| 0.9 |
OR9 |
A, B, C, D |
|
4.7 |
4R7 |
A, B, C, D |
| 1.0 |
1R0 |
A, B, C, D |
|
5.1 |
5R1 |
B, C, D |
| 1.1 |
1R1 |
A, B, C, D |
|
5.6 |
5R6 |
B, C, D |
| 1.2 |
1R2 |
A, B, C, D |
|
6.2 |
6R2 |
B, C, D |
| 1.3 |
1R3 |
A, B, C, D |
|
6.8 |
6R8 |
B, C, D |
| 1.4 |
1R4 |
A, B, C, D |
|
7.5 |
7R5 |
B, C, D |
| 1.5 |
1R5 |
A, B, C, D |
|
8.2 |
8R2 |
B, C, D |
| 1.6 |
1R6 |
A, B, C, D |
|
9.1 |
9R1 |
B, C, D |
| 1.7 |
1R7 |
A, B, C, D |
|
10 |
100 |
F, G, J, K |
| 1.8 |
1R8 |
A, B, C, D |
|
11 |
110 |
F, G, J, K |
| 1.9 |
1R9 |
A, B, C, D |
|
12 |
120 |
F, G, J, K |
| 2.0 |
2R0 |
A, B, C, D |
|
13 |
130 |
F, G, J, K |
| 2.1 |
2R1 |
A, B, C, D |
|
15 |
150 |
F, G, J, K |
| 2.2 |
2R2 |
A, B, C, D |
|
16 |
160 |
F, G, J, K |
| Custom Values Available - Contact Factory |
<< Back to R03S
<< Back to R03S
| Ordering Information |
|---|
 |
|
|
