R05W Information
R05W (0201) W-Series, Low ESR Capacitor Multi-Layer High-Q Capacitors
Specifications
| Electrical Specifications |
| Case Size: |
0201 |
| Capacitance: |
0.2 - 100 pF |
| Mechanical Characteristics |
| Size |
Units |
Length |
Width |
Thickness |
End Band |
| 0201 |
In |
.024 ±.001 |
.012 ±.001 |
.012 ±.001 |
.008 Max. |
| Mechanical Specifications |
| |
Specification |
Test Parameters |
| Solderability: |
Solder coverage = 90% of metalized
areas No termination degradation |
Preheat chip to 120°-150°C for 60 sec., dip terminals in rosin flux then dip in Sn62 solder @ 240°±5°C for 5±1 sec |
| Resistance to Soldering Heat: |
No mechanical damage
Capacitance change: ±2.5% or 0.25pF
Q>500 I.R. >10 G Ohms
Breakdown voltage: 2.5 x WVDC |
Preheat device to 80°-100°C for 60 sec. followed by 150°-180°C for 60 sec. Dip in 260°±5°C solder for 10±1 sec. Measure after 24±2 hour cooling period |
| Terminal Adhesion: |
Termination should not pull off. |
Linear pull force* exerted on axial leads soldered to each terminal. *0402 = 2.0lbs, 0603 = 2.0lbs (min.) |
| PCB Deflection: |
No mechanical damage.
Capacitance change: 2% or 0.5pF Max |
Glass epoxy PCB: 0.5 mm deflection |
| Environmental Specifications |
| |
Specification |
Test Parameters |
| Life test: |
No mechanical damage.
Capacitance change: ±3.0% or 0.3 pF
Q>500 I.R. >1 G Ohms
Breakdown voltage: 2.5 x WVDC |
Applied voltage: 200% rated voltage, 50 mA max.
Temperature: 125°±3°C
Test time: 1000+48-0 hours |
| Thermal Cycle: |
No mechanical damage.
Capacitance change: ±2.5% or 0.25pF
Q>2000 I.R. >10 G Ohms |
5 cycles of: 30±3 minutes @ -55°+0/-3°C,
2-3 min. @ 25°C, 30±3 min. @ +125°+3/-0°C,
2-3 min. @ 25°C
Measure after 24±2 hour cooling period |
| Humidity, Steady State: |
No mechanical damage.
Capacitance change: ±5.0% or 0.50pF max.
Q>300 I.R. = 1 G-Ohmbr /> Breakdown voltage: 2.5 x WVDC |
Relative humidity: 90-95%
Temperature: 40°±2°C
Test time: 500 +12/-0 Hours
Measure after 24±2 hour cooling period |
| Humidity, Low Voltage: |
No mechanical damage.
Capacitance change: ±5.0% or 0.50pF max.
Q>300 I.R. = 1 G-Ohm min.
Breakdown voltage: 2.5 x WVDC |
Applied voltage: 1.5 VDC, 50 mA max.
Relative humidity: 85±2% Temperature: 40°±2°C
Test time: 240 +12/-0 Hours
Measure after 24±2 hour cooling period |
| Vibration: |
No mechanical damage.
Capacitance change: ±2.5% or 0.25pF
Q>1000 I.R. = 10 G-Ohm
Breakdown voltage: 2.5 x WVDC |
Cycle performed for 2 hours in each of three perpendicular directions.
Frequency range 10Hz to 55 Hz to 10 Hz traversed in 1 minute. Harmonic motion amplitude: 1.5mm. |
| Capacitance Values |
| Value (pF) |
Cap Code |
Tolerances |
|
Value (pF) |
Cap Code |
Tolerances |
| 110 |
111 |
F, G, J, K |
|
1000 |
102 |
G, J, K |
| 220 |
221 |
F, G, J, K |
|
2200 |
222 |
G, J, K |
| 470 |
471 |
G, J, K |
|
4700 |
472 |
G, J, K |
| 680 |
681 |
G, J, K |
|
10000 |
103 |
G, J, K |
| 820 |
821 |
G, J, K |
|
|
|
|
| Ordering Information |
 |
|
RF Capacitors 
