Login     Register

R15S Information

R15S (0805) S-Series, Low ESR Capacitor Multi-Layer High-Q Capacitors

Specifications

 Electrical Specifications
Case Size: 0805
Capacitance: 0.3 - 220 pF
Mechanical Characteristics
Size Units Length Width Thickness End Band
0805 In .080 ±.008 .050 ±.008 .040 ±.006 .020 ±.010
 
 Mechanical Specifications
  Specification Test Parameters
Solderability: Solder coverage = 90% of metalized
areas No termination degradation
Preheat chip to 120°-150°C for 60 sec., dip terminals in rosin flux then dip in Sn62 solder @ 240°±5°C for 5±1 sec
Resistance to Soldering Heat: No mechanical damage
Capacitance change: ±2.5% or 0.25pF
Q>500 I.R. >10 G Ohms
Breakdown voltage: 2.5 x WVDC
Preheat device to 80°-100°C for 60 sec. followed by 150°-180°C for 60 sec. Dip in 260°±5°C solder for 10±1 sec. Measure after 24±2 hour cooling period
Terminal Adhesion: Termination should not pull off. Linear pull force* exerted on axial leads soldered to each terminal. *0805 = 2.0lbs, 0805 = 2.0lbs (min.)
PCB Deflection: No mechanical damage.
Capacitance change: 2% or 0.5pF Max
Glass epoxy PCB: 0.5 mm deflection
 Environmental Specifications
  Specification Test Parameters
Life test: No mechanical damage.
Capacitance change: ±3.0% or 0.3 pF
Q>500 I.R. >1 G Ohms
Breakdown voltage: 2.5 x WVDC
Applied voltage: 200% rated voltage, 50 mA max.
Temperature: 125°±3°C
Test time: 1000+48-0 hours
Thermal Cycle: No mechanical damage.
Capacitance change: ±2.5% or 0.25pF
Q>2000 I.R. >10 G Ohms
5 cycles of: 30±3 minutes @ -55°+0/-3°C,
2-3 min. @ 25°C, 30±3 min. @ +125°+3/-0°C,
2-3 min. @ 25°C
Measure after 24±2 hour cooling period
Humidity, Steady State: No mechanical damage.
Capacitance change: ±5.0% or 0.50pF max.
Q>300 I.R. = 1 G-Ohmbr /> Breakdown voltage: 2.5 x WVDC
Relative humidity: 90-95%
Temperature: 40°±2°C
Test time: 500 +12/-0 Hours
Measure after 24±2 hour cooling period
Humidity, Low Voltage: No mechanical damage.
Capacitance change: ±5.0% or 0.50pF max.
Q>300 I.R. = 1 G-Ohm min.
Breakdown voltage: 2.5 x WVDC
Applied voltage: 1.5 VDC, 50 mA max.
Relative humidity: 85±2% Temperature: 40°±2°C
Test time: 240 +12/-0 Hours
Measure after 24±2 hour cooling period
Vibration: No mechanical damage.
Capacitance change: ±2.5% or 0.25pF
Q>1000 I.R. = 10 G-Ohm
Breakdown voltage: 2.5 x WVDC
Cycle performed for 2 hours in each of three perpendicular directions.
Frequency range 10Hz to 55 Hz to 10 Hz traversed in 1 minute. Harmonic motion amplitude: 1.5mm.
 Capacitance Values*
Value (pF) Cap Code Tolerances   Value (pF) Cap Code Tolerances
0.3 OR3 A, B, C, D   9.1 9R1 B, C, D
0.4 OR4 A, B, C, D   10 100 F, G, J, K
0.5 OR5 A, B, C, D   11 110 F, G, J, K
0.6 OR6 A, B, C, D   12 120 F, G, J, K
0.7 OR7 A, B, C, D   13 130 F, G, J, K
0.8 OR8 A, B, C, D   15 150 F, G, J, K
0.9 OR9 A, B, C, D   16 160 F, G, J, K
1.0 1R0 A, B, C, D   18 180 F, G, J, K
1.1 1R1 A, B, C, D   20 200 F, G, J, K
1.2 1R2 A, B, C, D   22 220 F, G, J, K
1.3 1R3 A, B, C, D   24 240 F, G, J, K
1.4 1R4 A, B, C, D   27 270 F, G, J, K
1.5 1R5 A, B, C, D   30 300 F, G, J, K
1.6 1R6 A, B, C, D   33 330 F, G, J, K
1.7 1R7 A, B, C, D   36 360 F, G, J, K
1.8 1R8 A, B, C, D   39 390 F, G, J, K
1.9 1R9 A, B, C, D   43 430 F, G, J, K
2.0 2R0 A, B, C, D   47 470 F, G, J, K
2.1 2R1 A, B, C, D   51 510 F, G, J, K
2.2 2R2 A, B, C, D   56 560 F, G, J, K
2.4 2R4 A, B, C, D   62 620 F, G, J, K
2.7 2R7 A, B, C, D   68 680 F, G, J, K
3.0 3R0 A, B, C, D   75 750 F, G, J, K
3.3 3R3 A, B, C, D   82 820 F, G, J, K
3.6 3R6 A, B, C, D   91 910 F, G, J, K
3.9 3R9 A, B, C, D   100 101 F, G, J, K
4.3 4R3 A, B, C, D   110 111 F, G, J, K
4.7 4R7 A, B, C, D   120 121 F, G, J, K
5.1 5R1 B, C, D   130 131 F, G, J, K
5.6 5R6 B, C, D   150 151 F, G, J, K
6.2 6R2 B, C, D   160 161 F, G, J, K
6.8 6R8 B, C, D   180 181 F, G, J, K
7.5 7R5 B, C, D   200 201 F, G, J, K
8.2 8R2 B, C, D   220 221 F, G, J, K
Custom Values Available - Contact Factory
 RF Performance data



 Ordering Information
 
 

Part Locator
  • Part Number Search
  • RF Components
Sales Reps
Distributors
Corporate Responsibility
Prototyping Kits
Cross Reference Charts
Designer Libraries
Modeling Software
Johanson Technology, Inc.

4001 Calle Tecate
Camarillo, CA 93012

(805) 389-1166 phone
(805) 389-1821 fax
Copyright © 2014 Johanson Technology
All rights reserved.